Salt air destroys a crane remote control in a way no IP rating describes. A transmitter that passes a jet test and an immersion test can still be scrap within eighteen months on a quayside, because the failure is rarely water getting in. It is chloride attack on the enclosure screws, the antenna connector and the internal shielding, and it shows up first as range loss rather than as a dead unit.
If you are specifying for a port, a shipyard or any crane within a few hundred metres of open water, the protection question is chemistry, not ingress. This guide covers what salt attacks, why the IP code cannot answer for it, which materials are worth paying for, and the second port-specific problem: reach.

What salt air actually attacks
Sea air carries chloride as aerosol. It settles as a thin film, and because chlorides are hygroscopic that film stays wet far longer than the ambient humidity alone would allow, so every dew cycle rewets it. The result is an electrolyte sitting permanently on the outside of the transmitter, attacking three places in a predictable order.
First, any dissimilar metal joint. A stainless screw threaded into an aluminium or zinc-alloy housing is a galvanic couple, and the aluminium becomes the anode. Damage starts under the screw head where nobody looks. Second, the antenna connector, where a thin oxide layer raises contact resistance and quietly eats link margin. Third, the gasket seat, where corrosion lifts the sealing surface until the gasket no longer compresses evenly.
Salt damage is therefore progressive and mostly invisible. A transmitter in a container yard rarely dies suddenly. It loses range over two or three seasons, the operator compensates by walking closer, and then one day it fails at a distance that once worked.
Why the IP code cannot answer for salt
The IP code comes from IEC 60529 and answers one question: how well does the enclosure keep solid objects and water out under defined conditions. Those conditions use fresh water, no chlorides, no ultraviolet load, no thermal cycling and no wind-driven spray at an angle. A quayside does all five at once.
| Rating or test | What it actually proves | What it does not prove |
|---|---|---|
| IP65 | Dust-tight, resistant to water jets from a nozzle | Nothing about chloride attack, UV or long-term seal compression |
| IP67 | Survives temporary immersion at a stated depth and duration | Nothing about salt, and immersion is not repeated wetting |
| IP68 | Continuous immersion under conditions agreed with the supplier | Nothing about the joint between two different metals |
| ISO 9227 neutral salt spray | Corrosion resistance of the finish, in hours to red rust | Nothing about sealing performance or RF behaviour |
This is why two units with identical IP67 labels behave completely differently on the same quay. The label describes the seal and nothing else. It says nothing about whether the fixings are 304 or 316 stainless, whether the board is conformally coated, or whether the antenna connector still conducts after three hundred wetting cycles.
Materials and sealing choices worth paying for
When a port customer asks what changes against a standard workshop unit, these four items matter most per unit of cost.
Fixings and inserts. Specify 316 stainless, not 304 and never zinc-plated. 304 is adequate inland and marginal at the coast. Equally important is avoiding a bare aluminium thread, so look for threaded inserts or a housing that does not become the anode.
Gasket compound. EPDM and silicone resist UV and ozone; nitrile does not. The gasket also has to keep its compression set, because a gasket that takes a permanent set stops sealing long before it cracks.

Board protection. A conformal coating buys time against the condensation that forms inside any enclosure cycling in temperature daily. A transmitter carried from a cold night into a warm cabin will have water on the PCB whatever the gasket does, and coating stops that film from starting corrosion tracks.
Connector care. An external antenna connector should be a sealed type, capped when unused and assembled with dielectric grease, because that joint decides whether it still passes signal in year three.
Long reach and obstruction at the quayside
Quayside work breaks the assumptions behind a published operating distance. Every range figure you will be quoted assumes a clear line of sight between two antennas at a stated height. In a container yard the path runs through steel, and steel does not just attenuate the signal, it reflects it into the receiver out of phase.
Water adds a second effect. A flat sea surface is an excellent reflector, so the receiver sees the direct path and a delayed reflection at almost the same strength. In some positions they cancel. That is why an operator can hold a solid link at thirty metres and lose it completely at fifteen, and why the fault report says it only fails in one corner of the yard.
The fix is geometry, not power. Put the receiver antenna as high as the crane structure allows, above a stacked container where possible, and outside any metal cabinet. Keep it away from the drive cabinet and large vertical steel, and mount a vertical antenna vertically, because a polarisation mismatch alone costs more than most people expect. Where the geometry cannot be fixed, a repeater is the correct answer rather than a bigger transmitter.
Antenna siting, earthing and lightning
A quayside crane is the tallest steel structure for a few hundred metres, which makes its antenna the most exposed point in the area. The antenna needs a mounting with a metallic path to the crane structure, not a plastic bracket on a plastic cover, and the coaxial run needs surge protection where it enters the cabinet. A strike on the structure induces a large transient on a long coax screen even when nothing is hit directly.
Coax loss is the other half of this. Signal lost in cable is lost twice, on transmit and on receive, at every metre. Keep the receiver and antenna close together, and if the antenna must be remote-mounted, use low-loss cable sized for the frequency in use. A long run of thin cable turns a good receiver into a mediocre one. A deck hatch station adds hydraulics to that picture, because each button maps to a valve rather than a contactor, and hydraulic hatch control on marine cranes is where that mapping is decided.
What to put in a port crane enquiry
Port buyers get better answers when the enquiry states the environment rather than only the machine. Include these seven items.
- Distance from the normal operator position to the receiver, and whether the path is clear or runs through container stacks.
- Height and mounting position intended for the receiver and its antenna.
- Whether the crane works over water, and how far inland the quay line is.
- Any washdown regime, and whether directed hoses are used on the crane structure.
- Ambient temperature range, and whether the cabin is air-conditioned.
- Local radio approval required for the port’s country, and the band already in use on site.
- Whether the site has a lightning protection scheme the new equipment must bond into.
The band already in use and the intended antenna height are the two most often omitted, and the two that most often force a redesign after delivery. If the port already runs a radio system, a new crane remote has to coexist with it, which is a selection question rather than an installation one. How the two common bands behave in dense steel is set out in 433 MHz versus 2.4 GHz for crane remote control, and the sealing argument in IP65 versus IP67.
Shipyard work is often not a crane at all but a hydraulic hatch or hold cover, and those have their own sealing and handle layout requirements. A hydraulic hatch control box is a different product from a handheld transmitter, and specifying one when the other is needed causes real delay.
For a system sized to a specific quay, send the seven items above with the crane type and we will confirm receiver configuration, antenna arrangement and enclosure specification against them. Start from the industrial crane remote control system page or send the site details directly.
FAQ
Is IP67 enough for a quayside crane?
IP67 covers immersion but says nothing about chlorides, so it is necessary and not sufficient. Treat it as the minimum sealing level and specify the corrosion items separately: 316 stainless fixings, EPDM or silicone gaskets, conformal coating and a sealed antenna connector.
How long does a standard transmitter last at the coast?
It depends on finish and maintenance rather than on the radio design. Units with plated screws and uncoated boards commonly show range loss within two seasons, while a unit with marine-grade fixings and a coated board usually gives several years.
Can we keep the transmitter in the cabin to protect it?
A closed cabin helps with direct spray and hurts with condensation, because the cabin cycles in temperature and the transmitter is repeatedly brought from cold to warm. If the cabin is not climate-controlled, a ventilated store at stable temperature is usually better.
Why does the remote work everywhere except one corner of the yard?
That pattern points to multipath rather than a weak transmitter. Reflections from container stacks and the water surface arrive out of phase at specific positions and cancel the direct signal. Moving the antenna higher and away from large vertical steel normally fixes it; more power rarely does.
Do we need a different model for shipyard use than for a container terminal?
Not necessarily, but the antenna arrangement and control layout usually differ. Container cranes need long reach with the receiver mounted high, while shipyard work often involves hatch covers and hold equipment where a fixed control box is the right answer.
