A crane remote control release should end the movement. When the load keeps travelling after the button comes up, the radio is almost never the cause, yet it is blamed first because the transmitter is what the operator is holding. The useful question is which of the four things between the button and the drum is still moving, and how to find out in ten minutes.
How Much Drift Is Normal, and How Much Is Not
Some movement after release is designed in. The hoist decelerates, the brake sets, and the hook settles. The field allowance is roughly 25 mm of hook travel per 3 m/min (10 ft/min) of hoist speed, measured from release to standstill, and less under a full load. A hoist rated at 6 m/min should therefore settle about 50 mm.
Beyond that allowance, or any downward movement that continues after the hook has clearly stopped, is not settling. It is the holding brake failing to develop its rated torque.
| What you see | What usually owns it | First check |
|---|---|---|
| Hook settles a few millimetres and stops | Normal release drift | Compare with the 25 mm per 3 m/min allowance |
| Load keeps descending slowly, no sound | Holding brake torque: worn lining, oil, wide gap, tired spring | Air gap with a feeler gauge, lining, oil traces |
| Load drops again about a third of a second later | Release timing: receiver output, contactor, drive stop sequence | Measure release time at the contactor |
| Every stop is late, hook overshoots | VFD brake delay or stop sequencing | Brake engage delay and holding-torque parameters |
| Only noticeable with a heavy load | Brake torque margin, or a load brake not holding | Static hold test at rated load |
| Brake housing hot, faint burning smell | Brake dragging because it never fully releases | Coil voltage and rectifier, then gap |
The Four Causes Behind a Load That Keeps Creeping
Brake condition. A spring-applied, electrically released brake sets by spring force and opens only when the coil is energised. Wear widens the air gap, so the armature travels further before it clamps. Oil from a leaking gearbox seal collapses the friction coefficient even with plenty of lining left. A spring that has taken a set delivers less clamping force than the design assumed.
Electrical release time. The coil is fed through a contactor or rectifier. Low coil voltage, a failing rectifier, a dirty terminal or a slow relay all delay the set, so a mechanically sound brake holds the load late.
VFD stop sequencing. On an inverter hoist the drive must keep producing torque until the mechanical brake has closed. If torque collapses first, a suspended load creeps in that window. If the brake closes first, the drive fights it. Both are parameter problems, not hardware problems.
Mechanical slack. Coupling clearance, worn gears, a loose brake drum and slack rope add travel that looks like drift but is not brake slip.

Ten Minutes That Separate Electrical From Mechanical
The point of this sequence is to produce a number, not an opinion. Clear the area below the hook and stay within the hoist rating.
- Log the conditions: load weight, speed step, contactor or inverter control, and whether the fault appears cold or after half an hour. A fault that only appears hot points at friction.
- Mark the rope with tape against a fixed reference, lower at full speed, release, and measure the travel before standstill. Repeat three times and keep the worst figure.
- Repeat at slow speed. Drift that scales with speed is normal settling; a figure that stays the same in millimetres regardless of speed is brake slip.
- Listen at the panel while a second person works the handset. The hoist contactor should drop out almost with the brake. A noticeable gap is release timing.
- Meter the brake coil: pick-up and drop-out voltage, and how long the voltage takes to decay. Anything below coil rating at drop-out explains a late set.
- Write the result in the crane log. A trend across months matters more than one reading, because wear is gradual and the operator’s compensation hides it.
If the number is within allowance and the brake is cool, stop there. Adjusting a brake that behaves correctly is how good brakes get ruined.
Why the Load Drops Again After a Two-Speed Stop
Two-speed hoists give a characteristic double settle: the hoist decelerates out of fast, holds on slow, the operator releases, the load drops as the slow contactor opens and then again a fraction of a second later. The second step is a release timing artefact, and it grows when the receiver holds its hoist outputs longer than the contactor needs.
Direction matters too. A load lowered, stopped, raised slightly and lowered again arrives at the stop with a warm brake and the gear train loaded the other way. Expect a longer settle and do not diagnose from one stop after a direction change.
What the Radio and the Receiver Actually Contribute
A radio link cannot make a load drift once every output has opened. What it can do is delay the opening. Relay outputs drop out in the order of ten milliseconds; solid-state outputs are faster but behave differently when driving a large contactor coil, and a release delay programmed for another purpose holds the hoist output closed after release. Relay versus solid-state receiver outputs covers the difference, and it is worth knowing whether the hoist command is momentary or maintained, because momentary and maintained outputs fail differently.
Two receiver faults get confused with brake drift. A stuck output keeps the contactor energised, so the hoist keeps running rather than creeping, which is a different and more dangerous symptom. A receiver losing signal mid-lift drops all outputs at once and produces a single heavier settle. Both are ruled out with how to bench-test a crane remote control receiver, and the figures to compare against are in crane remote control response time. If the crane stops responding rather than drifting, the fault is upstream of the brake and the wiring and supply are the first things to check.

When to Take the Crane Out of Service
Drift within allowance with a cool brake is a maintenance note. Drift that grows within a shift, drift under a load you have lifted all week, or a hot smelling brake is an out-of-service condition: land the load, isolate the crane and hold the hook clear until the brake passes a hold test. The usual criterion is a test load of about ten percent of rated capacity, held ten minutes, with no measurable movement.
Send a supplier the measurement rather than the theory: the drift figure at both speeds, the load weight, contactor or inverter control, the receiver model and output type, and the age of the brake. Those five items tell a supplier whether the fix is a brake kit, a drive parameter or a receiver setting. For multi-motion cranes the receiver is usually the industrial crane remote control system; for a single-hoist unit often an eight-function wireless remote control. Both can be specified in one pass through the contact form.
FAQ
Is some drift after releasing the hoist button normal?
Yes. About 25 mm of hook travel per 3 m/min of hoist speed, less under full load. What is not normal is movement after the hook has stopped, or a figure that grows month to month.
Can a radio remote control cause the load to drift?
Only by delaying the command. Once the outputs are open the radio has no further influence, so a creeping load is a brake, contactor, drive or mechanical issue.
Why does the load drop twice on a two-speed hoist?
The fast contactor opens first, the hoist briefly runs on slow, then the slow contactor opens and the load settles again. A release delay in the receiver makes the second step larger.
Should I adjust the brake to stop the drift?
Adjust the air gap only to the manufacturer’s figure, and only after measuring. A glazed or oil-contaminated lining has to be replaced. If drift is within allowance, leave the brake alone.
How do I know it is the brake and not the drive?
Measure at full speed and at slow speed. Settling scales with speed; brake slip stays roughly the same in millimetres. A late stop on every cycle with a cool brake points at the drive.
